RESEARCH ON CUTTING FORCES AND CUTTING TEMPERATURE IN ORTHOGONAL CUTTING SOFTWOOD AND HARDWOOD PARALLEL TO GRAIN

Authors

  • Xu Bao Faculty of Material Science and Engineering Nanjing Forestry University
  • Xiaolei Guo Faculty of Material Science and Engineering Nanjing Forestry University
  • Pingxiang Cao Faculty of Material Science and Engineering Nanjing Forestry University
  • Linlin Xie Faculty of Landscape Architecture Nanjing Forestry University
  • Minsi Deng Faculty of Material Science and Engineering Nanjing Forestry University

Keywords:

cutting forces, cutting temperature, orthogonal cutting, coniferous wood, broad-leaved wood,

Abstract

Experimental results showed that the cutting force and cutting zone temperature of soft pine were lower than that of hard oak under the same cutting condition, and the influence degree of chip type on the cutting force of soft pine is lower than that of hard oak. Different chip formation shows little or no effect on cutting temperature in processing both soft pine and hard oak.

References

Costes JP, Ko PL, Ji T, Decespetit C, Altintas Y (2004)

Orthogonal cutting mechanics of maple: Modeling a solid

wood-cutting process. J Wood Sci 50(1):28-34.

Fengel D, Wegener G, Fengel D, Wegener G (2003) Wood:

Chemistry, ultrastructure, reactions. Holz Roh Werkst

(8):314-314.

Guo XL, He JL, Qing ZH, Wei H, Cao PX (2017a) Tribological

properties of coated tool materials and woodbased

materials. Linye Kexue 539(11):164-169.

Guo XL, Lin YB, Na B, Liang XY, Ekevad M, Ji FT, Huang

LL (2017b) Evaluation of physical and mechanical properties

of fiber-reinforced poplar scrimber. BioResources

(1):43-55.

Guo XL, Zhu ZL, Ekevad M, Bao X, Cao PX (2018) The

cutting performance ofAl2O3 and Si3N4 ceramic cutting tools

in the milling plywood. Adv Appl Ceramics 117(1):16-22.

Gonçalves R, Neri AC (2005) Orthogonal cutting forces in

juvenile and mature Pinus taeda wood. Sci Agric 62(4):

-318.

Koch P (1964) Wood machining processes. The Ronald Press

Company, New York, NY. 23 pp.

Li WG (2017) The influences of circular saws with sawteeth

of mic-zero-degree radial clearance angles on surface

roughness in wood rip sawing. Ann For Sci 74(2):37-39.

Pizzi A (1994) Advanced wood adhesives technology. M.

Dekker 15(3):198-199.

Qian XY (2010) Current status and future challenges of

wood-based panel industry in China. China Wood Industry

:15-18.

Ratnasingam J, Ma TP, Ramasamy G (2009) Tool temperature

and cutting forces during the machining of particleboard

and solid wood. J Appl Sci (Faisalabad) 10(22):

-2886.

Reiterer A, Burgert I, Sinn G, Tschegg S (2002) The radial

reinforcement of the wood structure and its implication on

mechanical and fracture mechanical properties—A comparison

between two tree species. J Mater Sci 37(5): 935-940.

Silva MBD, Wallbank J (1999) Cutting temperature: Prediction

and measurement methods—A review. J Mater Process Technol 88(1-3):195-202.

Wang SY, Zhao J, Meng H, Ai X, Li ZL (2004) Numeric

investigation of the cutting temperature fields on the rake

face in orthogonal machining. Mater Sci Forum 471-472:

-551.

Wyeth DJ, Goli G, Atkins AG (2009) Fracture toughness,

chip types and the mechanics of cutting wood. A review.

Holzforschung 63(2):168-180.

Zhu ZL, Guo XL, Ekevad M, Cao PX, Na B (2017) The

effects of cutting parameters and tool geometry on cutting

forces and tool wear in milling high-density fiberboard with

ceramic cutting tools. Int J Adv Manuf Technol 91(9-12):

-4041.

Downloads

Published

2018-10-30

Issue

Vol. 50 No. 4 (2018)

Section

Technical Notes

License

The copyright of an article published in Wood and Fiber Science is transferred to the Society of Wood Science and Technology (for U. S. Government employees: to the extent transferable), effective if and when the article is accepted for publication. This transfer grants the Society of Wood Science and Technology permission to republish all or any part of the article in any form, e.g., reprints for sale, microfiche, proceedings, etc. However, the authors reserve the following as set forth in the Copyright Law:

1. All proprietary rights other than copyright, such as patent rights.

2. The right to grant or refuse permission to third parties to republish all or part of the article or translations thereof. In the case of whole articles, such third parties must obtain Society of Wood Science and Technology written permission as well. However, the Society may grant rights with respect to Journal issues as a whole.

3. The right to use all or part of this article in future works of their own, such as lectures, press releases, reviews, text books, or reprint books.