Development of an Acousto-Ultrasonic Scanning System for Nondestructive Evaluation of Wood and Wood Laminates

Authors

  • Jacek M. Biernacki
  • Frank C. Beall

Keywords:

Acousto-ultrasonics, adhesive bond, orthotropy, modulus of elasticity, growth ring angle

Abstract

An acousto-ultrasonic (AU) scanning system was developed and optimized for wood products. It was found that AU probe alignment, coupling pressure, and stabilization time affect the repeatability of AU readings. After optimization of these factors, the error in AU reading (RMS) was negligible. AU transmission through solid wood also showed a relationship of acoustic attenuation to wood anisotropy. A calculated modulus of elasticity in the direction of wave propagation correlated with wave attenuation characteristics in the TR and LR planes. For wave propagation in the TR plane, the greatest attenuation was observed at a growth ring angle (GRA) of about 45°, corresponding to the lowest modulus of elasticity, which is in this plane. The effect of wood anisotropy (GRA) was found to be a major problem for evaluation of laminated wood, since the received signal was strongly affected by wood properties. Consequently, the effect of anisotropy and natural variability of wood will be the major limiting factor of any acoustic NDE technique applied to many wood products.

References

Beall, F. C. 1990. Use of AE/AU for evaluation of adhesively-bonded wood-base materials. Pages 45-53 in Proceedings, Seventh International Symposium on Nondestructive Testing of Wood, Madison, WI.nBeall, F. C. 1991. Nondestructive evaluation of adhesion using acousto-ultrasonics. Pages 97-102 in Proceedings, Wood Adhesives 1990, Madison, WI.nBeall, F. C., and J. M. Biernacki. 1992a. An approach to the evaluation of glulam beams through acousto-ultrasonics. Pages 73-88 in Proceedings, Eighth International Symposium on Nondestructive Testing of Wood, September 1991. Vancouver. WA.nBeall, F. C., and J. M. Biernacki. 1992b. Detection of adhesion flaws in parallel laminates of lumber using acousto-ultrasonics. In Proceedings, Adhesives and Bonded Wood Symposium, November 1991, Seattle, WA (in press).nBiernacki, J. M. 1991. Bond quality evaluation of laminated timbers with acousto-ultrasonics. M.S. thesis. University of California at Berkeley, Berkeley. CA. 128 pp.nBodig, J., and B. A. Jayne. 1982. Mechanics of wood and wood composites. Van Nostrand, New York, NY. 712 pp.nDuke, J. C., and M. T. Kiernan. 1988. Predicting damage development in composite materials based on AU evaluation. Pages 191-200 in J.C. Duke, Jr., ed. Acousto-ultrasonics: Theory and applications. Plenum Press, NY.nFahr, A., S. Lee, S. Tanary, and Y. Haddad. 1988. Estimation of strength in adhesively bonded steel specimens by acousto-ultrasonic technique. Material Evaluation 47(2):233-240.nGreen, A. T. 1990. Qualification of particleboards on the mill line. Pages 149-160 in H. dos Reis, ed. Nondestructive testing and evaluation in manufacturing and construction. Hemisphere Publishing Co., New York, NY.nGreen, R. E. 1991. Ultrasonic waves in anisotropic materials: Past, present and future. 1991 ASNT Fall Conference and Quality Testing Show. September 1991, Boston, MA. Pp. 42-46.nKiernan, M. T., and J. C. Duke, Jr. 1988. Acousto-ultrasonics as a monitor of material anisotropy. Material Evaluation 46(8):1105-1113.nKiernan, M. T., and J. C. Duke, Jr. 1990. A physical model for the acousto-ultrasonic method. NASA Contractor Report 185294. 262 pp.nLemaster, R. L., and D. A. Dornfeld. 1987. Preliminary investigation on the feasibility of using acousto-ultrasonics to measure defects in lumber. J. Acoustic Emission 6(3):157-163.nLord, W., R. Ludvig, and Z. You. 1988. Finite element modeling of ultrasonic wave propagation in materials. Pages 1-7 in New directions in the nondestructive evaluation of advanced materials, Winter Annual Meeting of Mechanical Engineers, November 1988, Chicago, IL.nMitchell, J. R. 1988. Multi-parameter, multi-frequency acousto-ultrasonic for detecting impact damage in composite. Pages 311-312 in J. C. Duke, Jr., ed. Acousto-ultrasonics: Theory and applications. Plenum Press, New York, NY.nMusgrave, M. J. P. 1970. Crystal acoustics. Holden-Day, San Francisco, CA. 288 pp.nPatton-Mallory, M., and R. C. De Groot. 1989. Detecting brown-rot decay in southern yellow pine by acousto-ultrasonics. Pages 29-43 in Proceedings, Seventh Symposium of Nondestructive Testing of Wood, Pullman, WA.nPatton-Mallory, M., K. D. Anderson, and R. C. De Groot. 1987. An acousto-ultrasonic method for evaluating decayed wood. Pages 167-182 in Proceedings, Sixth Symposium of Nondestructive Testing of Wood, Pullman. WA.nDos Reis, H. L. M. 1989. Non-destructive evaluation of adhesive bond strength in laminated wood beams. British J. Non-Destructive Testing 31(12):675-679.nDos Reis, H. L. M., and D. A. McFarland. 1986. On the acousto-ultrasonic characterization of wood fiber hardboard. J. Acoustic Emission 5(2):67-70.nDos Reis, H. L. M., F. C. Beall., J. V. Carnahan, M. J. Chica, K. A. Miller, and V. M. Klick. 1990a. Nondestructive evaluation/characterization of adhesive bonded connections in wood structures. Pages 197-207 in H. L. M. dos Reis, ed. Nondestructive testing and evaluation for manufacturing and construction. Hemisphere Publishing Co., New York. NY.nDos Reis, H. L. M., D. A. McFarland, M. J. Chica, and D. W. Caster. 1990b. Nondestructive evaluation of adhesive bond strength of finger joints in structural lumber using the acousto-ultrasonic approach. J. Acoustic Emission 9(3):196-202.nVary, A. 1989. The acousto-ultrasonic approach. Pages 1-21 in J. C. Duke, Jr., ed. Acousto-ultrasonics: Theory and applications. Plenum Press, New York, NY.nVary, A., and R. F. Lark. 1979. Correlation of fiber composite tensile strength with the ultrasonic stress wave factor. J. Testing Eval. 7(4):85-191.n

Downloads

Published

2007-06-22

Issue

Number 3 / July 1993

Section

Research Contributions

License

The copyright of an article published in Wood and Fiber Science is transferred to the Society of Wood Science and Technology (for U. S. Government employees: to the extent transferable), effective if and when the article is accepted for publication. This transfer grants the Society of Wood Science and Technology permission to republish all or any part of the article in any form, e.g., reprints for sale, microfiche, proceedings, etc. However, the authors reserve the following as set forth in the Copyright Law:

1. All proprietary rights other than copyright, such as patent rights.

2. The right to grant or refuse permission to third parties to republish all or part of the article or translations thereof. In the case of whole articles, such third parties must obtain Society of Wood Science and Technology written permission as well. However, the Society may grant rights with respect to Journal issues as a whole.

3. The right to use all or part of this article in future works of their own, such as lectures, press releases, reviews, text books, or reprint books.