Open Access Open Access  Restricted Access Subscription or Fee Access

Effect of Coating Thickness on Sound Absorption Property of Four Wood Species Commonly Used for Piano Soundboards

Wei Xu, Xiaoyang Fang, Jiatong Han, Zhihui Wu, Jilei Zhang

Abstract


Effects of polyurethane (PU) coating thicknesses (0.15, 0.30, 0.45, and 0.60 mm) on sound absorption coefficients of four wood species were investigated using the standing wave ratio method with an input sound vibration frequency range set between 125 and 4000 Hz. Wood species of four specific gravity (SG) levels were Korean spruce, European spruce, Sitka spruce, and Picea brachytyla. Experimental results indicated that PU coating can significantly increase sound absorption coefficients of higher SG species such as Sitka spruce and Picea brachytyla in all tested frequency levels, but this significant increase was not observed in lower SG species such as Korean and European spruces when tested in the frequency range from 800 to 2000 Hz. Effects of coating thickness on sound absorption coefficients of four evaluated species were found to interact with wood SG values and input sound vibration frequency ranges. Specifically, coating 0.30-mm-thick PU on Korean and European spruces tends to result in significantly lower sound absorption coefficients among the ones coated with four evaluated thicknesses when tested at the frequency less than 800 Hz, but PU coating thickness resulting in lower sound absorption coefficients on Sitka spruce and Picea brachytyla was 0.15 mm. Sitka spruce and Picea brachytyla coated with 0.30- and 0.6-mm-thick PU had lower sound absorption coefficients when tested at the frequency ranging from 1000 to 2000 Hz. When tested at the frequency greater than 2500 Hz, sound absorption coefficients of four coated species increased as coating thickness increased from 0.30 to 0.60 mm with an increment of 0.15 mm, but these four species coated with three thicker PU had significantly lower sound absorption coefficients than the ones coated with 0.15-mm-thick PU. The uncoated higher SG species tended to have lower sound absorption coefficients than uncoated lower SG ones when tested in the frequency ranging from 500 to 4000 Hz, but the differences were not found when tested under the frequency less than 400 Hz. Coating four species with different thicknesses of PU could alter their SG effects on their sound absorption coefficients.


Keywords


Piano soundboard, spruce wood, coating thicknesses, specific gravity, sound absorption coefficient

Full Text:

PDF

References


Bucur V, Clement A, BitschM(1999) Acoustic properties of resonance wood and distribution of inorganic components of the cell wall. Holz Roh Werkst 5(57):103-104.

Cai JB, Li T (2011) Influence of two high-humidity thermal treatments on moisture absorption behavior of spruce wood planks. J For Eng 25(6):80-82.

Chrisler VL (1940) Effect of paint on the sound absorption of acoustic materials. Research Paper RP1298. Journal of Research of the National Bureau of Standards 24:547-553.

CNS (2009a) GB 1933-2009. Method for determination of the density of wood. China National Standard, Beijing, China.

CNS (2009b) GB 1931-2009. Method for determination of moisture content of wood. China National Standard, Beijing, China.

CNS (2013) GB T4893.5-2013. Test of surface coatings of furniture-Part 5: Determination of thickness. China National Standard, Beijing, China.

CNS (2004) GB T18696.1-2004. Acoustics-Determination of sound absorption coefficient and impedance in impedance tubes-Part 1: Method using standing wave ratio. China National Standard, Beijing, China.

Guan MJ, Gao J, Zhu YX (2009) Comparison of sound absorption properties between sympodial bamboo flooring and moso bamboo flooring. J For Eng 23(1):29-31.

Ivanova Y, Vitchev P, Hristodorova D (2018) Study on the influence of some factors on the sound absorption characteristics of wood from Scots pine. Chip Chipless Woodwork Process 11(1):65-72.

Jin XB (2008) The depth cognition of the piano tuning (Nine)—Discussion of the piano timbre (Mid). Musical Instrument Magazine 11(12):12-15.

Liu YX, Shen J, Tian ZL, Gang YJ, Hetian CJ (2001) Study on relationship between sound vibration parameters and growth ring width and latewood percentage of Picea genera wood. Sci Silvae Sin 37(6):86-91.

Luo JF, Zhang CH, Xu W, Wu ZH, Cai JB, Li T (2009) Manufacturing process of the piano sound board. Wood Process Mach 26(6):45-47.

Ma LN (2005) Study on relationships between wood structures and acoustic vibration properties. Anhui Agricultural University, Hefei, China. pp. 48-50.

Miu LZ (1983) The piano soundboard wood. Musical Instrument Magazine 23(3):15-16.

Shen J, Liu YX, Liu M, Liu Y, Gang YJ, Hetian CJ (2005) Effects of variance coefficient of growth ring width on sound vibration parameters of Picea wood. J North East For Univ 25(3):27-29.

Shen J, LiuYX, Tian ZL, Gang YJ, Hetian CJ (2001) Relationship between Picea genera wood density and sound characteristic parameters. J Huazhong Agric Univ 20(2):181-184.

Suzuki H (1986) Vibration and sound radiation of a piano soundboard. J Acoust Soc Am 77(6):33-35.

Wang JF, Huang SZ, Peng LM, Lei FJ, Lin JC (2015) Effects of microstructure of balsa wood on sound absorption properties. J Wood Process Mach 26(5):34-37.

Wu Y, Wu JM, Yang F, Tang CY, Huang QT (2019a) Effect of H2O2 bleaching treatment on the properties of finished transparent wood. Polymers (Basel) 11(5):776.

Wu JM, Wu Y, Yang F, Tang CY, Huang QT (2019b) Impact of delignification on morphological, optical and mechanical properties of transparent wood. Compos Part A Appl Sci Manuf 2019(117):324-331.

Yan XX, Qian XY, Lu R, Miyakoshi T (2018) Comparison and optimization of reactive dyes and coating performance on Fraxinus mandshurica veneer. Polymers (Basel) 10(12):1302.

Zou XL (2007) The piano soundboard materials and processing technology. Entertainment Technology 3: 55-58.


Refbacks

  • There are currently no refbacks.