Effects of Microstructural Heterogeneity in Cement Excelsior Board

Authors

  • Douglas C. Stahl
  • Steven M. Cramer
  • Robert L. Geimer

Keywords:

Heterogeneous microstructure, network modeling, progressive failure, wood composites

Abstract

Heterogeneity in the properties and arrangement of constituents can have an important effect on a composite's properties. This paper evaluates the effects of variability in wood strand dimensions, mechanical properties, and orientation on the engineering properties of cement excelsior board. The finite element method is used to analyze a heterogeneous three-dimensional microstructure of strands, predicting elastic and strength properties. Results suggest that variability in strand mechanical properties can significantly lower composite tensile and compressive strengths, while composite stiffness is not affected. The model also predicts that relatively modest alignment of strands can lead to significant increases in composite strength and stiffness in the direction of alignment.

References

Bodig, J., and B. A. Jayne. 1982. Mechanies of wood and wood composites. Van Nostrand, New York. 712 pp.nDai, C., and P. R. Steiner. 1994. Spatial structure of wood composites in relation to processing and performance characteristics, Part 2: Modeling and simulation of a randomly-formed flake layer network. Wood Sci. Technol. 28(2):135-146.nDeng, M., and C. T. J. Dodson. 1994. Paper: An engineered stochastic structure. TAPPI Press, Atlanta, GA. 284 pp.ndeWit, J. 1989. The Elten system. Pages 68-70 in Proc. Fiber and Particleboards with Inorganic Binders. Forest Products Society, Madison, WI.nHachmi, M., and A. B. Campbell. 1989. Wood-cement chemical relationships. Pages 43-47 in Proc. Fiber and Particleboards with Inorganic Binders. Forest Products Society, Madison, WI.nLang, E. M., and M. P. Wolcoti. 1995. Modeling the consolidation of wood strand mat. Mechanics of cellulosic materials, ASME AMD209/MD60:153-176.nMindness, S., and J. F. Young. 1981. Concrete. Prentice Hall, Englewood Cliffs, N.J. 671 pp.nPablo, A. A., D. A. Eusebio, M. G. Olea. 1990. Wood wool cement boards: A low cost panel from indigenous materials. Forest Products Technoflow Series 9. Forest Products Research and Development Instiute, Dept. of Science and Technology, Philippines. 12 pp.nRaisanen, V. I., M. J. Alava, R. M. Nieminen, and K. J. Niskanen. 1995. Elastic-plastic random fiber networks. Pages 109-112 in Proc. 1995 International Paper Physics Conference. TAPPI Press, Atlanta, GA.nShah, S. P., and C. Ouyang. 1991. Mechanical behavior of fiber-reinforced cement-based composites. J. Am. Ceramic Soc. 74(11):2727-2738.nShigekura, Y. 1989. Wood fiberboards bonded with inorganic binders in Japan. Pages 141-150 in Proc. Fiber and Particleboards with Inorganic Binders. Forest Products Society, Madison, WI.nSoroka, I. 1980. Portland cement paste and concrete. Chemical Publishing Co., Inc. New York, NY. 338 pp.nStahl, D. C. 1996. Micromechanical model for a wood-cement composite. Ph.D. dissertation, University of Wisconsin-Madison, Madison, WI. 177 pp.nStahl, D. C., and S. M. Cramer. 1997. A three-dimensional model for a low density fibrous composite. ASME J Eng. Mat. Technol. (in review).nUSDA. 1987. Wood handbook: Wood as an engineering material. Agricultural Handbook 72. U.S. Department of Agriculture, Washington, D.C. 431 pp.n

Downloads

Published

2007-06-19

Issue

Number 4 / October 1997

Section

Research Contributions

License

The copyright of an article published in Wood and Fiber Science is transferred to the Society of Wood Science and Technology (for U. S. Government employees: to the extent transferable), effective if and when the article is accepted for publication. This transfer grants the Society of Wood Science and Technology permission to republish all or any part of the article in any form, e.g., reprints for sale, microfiche, proceedings, etc. However, the authors reserve the following as set forth in the Copyright Law:

1. All proprietary rights other than copyright, such as patent rights.

2. The right to grant or refuse permission to third parties to republish all or part of the article or translations thereof. In the case of whole articles, such third parties must obtain Society of Wood Science and Technology written permission as well. However, the Society may grant rights with respect to Journal issues as a whole.

3. The right to use all or part of this article in future works of their own, such as lectures, press releases, reviews, text books, or reprint books.